Skip to content
VECA

November 17, 2026 · 6 min read

Window condensation: why windows sweat and how to stop it

Why windows fog up and run with water in winter, when it is a defect and when it isn't, and what prevents it: humidity, double glazing, low-E and better frames.

ResidentialThermal performanceGlass
Insulated glass line at the VECA plant

The first cold front reaches Monterrey and, the next morning, the windows are fogged. Sometimes it is just a haze in the corners. Other times water runs down to the track, the sealant turns black and mold appears on the wall under the window.

Condensation is almost never a defect in the window. It is physics: humid air touching a cold surface. But the window does decide how cold that surface gets, which is why two houses with the same humidity can have completely different glass. This guide explains where the water comes from, when to worry, and what prevents it.

The dew point

Air always carries water vapor, and the warmer it is, the more it can hold. When that air touches a cold surface it cools too. Below a certain temperature it can no longer hold all its vapor, and the excess turns to liquid water on the surface. That temperature is the dew point.

An example: a living room at 21 °C (70 °F) and 55 % relative humidity has a dew point of about 11.6 °C (53 °F). Any surface in that room colder than that will get wet.

Why it is always the window

The window is almost always the coldest surface in a room. A plastered masonry wall insulates several times better than single glass, so while the inside face of the wall stays close to room temperature, the inside face of the glass drifts toward the temperature outdoors.

How cold it gets depends on each part's U-value: the higher it is, the more heat escapes and the colder its inner face. Try it on a cold-front morning:

Will the window sweat?

Glass
Frame
Dew point
11.6 °C
Inner glass surface
8.4 °C · Condenses
Inner frame surface
8.0 °C · Condenses
A one-dimensional calculation, at the centre of the glass and on the frame. The glass edges and frame corners run slightly colder than these figures, which is why water shows up there first.Dew point: Magnus formula · Rsi 0.13 m²K/W (EN ISO 6946) · Ug: EN 673 · Uf: ISO 10077

At 4 °C (39 °F) outside, 21 °C inside and 55 % humidity, single glass sits at about 8.5 °C on its inner face: three degrees below the dew point, and it runs with water. The same room with clear double glazing keeps the surface above 14 °C, and the glass stays dry. An aluminum frame with no thermal break gets wet at almost the same time as single glass; with a thermal break or vinyl it holds out much longer.

Where it shows up first

Even if the middle of the glass is dry, water can appear at certain spots, because the surface there is colder than average:

  • The edge of the glass. In a double unit, the spacer that holds the panes apart is usually aluminum and conducts cold to the perimeter. That is why you often see a fogged band a few centimeters wide around the glass. A warm-edge spacer (plastic or composite) greatly reduces it.
  • The bottom. Air cooled against the glass sinks, so the lower part runs colder than the top.
  • Frame corners, where heat escapes in two directions.
  • Behind heavy curtains. A curtain against the glass shields the window from the room's heat, but not from its vapor. Behind it the glass gets colder and wetter.

Three different kinds of condensation

Not all water on a window is the same problem.

On the room side. The common one: indoor humidity plus a cold surface. It is solved by lowering the humidity, raising the surface temperature, or both.

Inside the double-glazed unit. If the fog is between the two panes and won't wipe off from either side, the unit's seal has failed and humid air has got into the cavity. There is no fix: the glass unit has to be replaced. The frame can normally stay.

On the outside. Sometimes, on cool damp mornings, the glass is wet outside. It happens mostly with low-E double glazing, because it insulates so well that the outer pane gets almost no heat from the house and cools like the lawn. It is not a defect; it is a sign the window is insulating. The sun dries it.

Where all that moisture comes from

A house produces vapor all day. The usual sources:

  • People. Breathing and perspiring, especially in bedrooms closed at night. That is why the bedroom is usually the room that wakes up most fogged.
  • Showers and cooking, without an exhaust fan or with one that isn't used.
  • Laundry drying indoors.
  • Unvented gas heaters. Very common in Monterrey in winter. Burning gas produces water vapor that stays in the room, on top of the carbon monoxide risk. A heater on all night in a closed bedroom is a perfect recipe for streaming windows.
  • Plants, aquariums and humidifiers.

What to do: lower the humidity

First, because it costs nothing:

  • Run the bathroom exhaust fan during the shower and a few minutes after, and the range hood when cooking.
  • Air the house each morning: five or ten minutes with windows open renews the air without chilling the walls.
  • Don't dry laundry indoors in the cold season.
  • If you use a gas heater, it should vent outside; or switch to electric heat or a heat-pump mini-split.
  • Leave space between the curtain and the glass, or open it during the day.

A cheap hygrometer helps a lot: in winter, indoor humidity of 40–50 % is comfortable and keeps a reasonable window dry.

What to do: raise the surface temperature

If the window still runs with normal humidity, the window is the weak point. What works, in order of impact:

  1. Double glazing. The biggest step: it takes the inner glass face from about 8.5 °C to almost 15 °C in the example above.
  2. A low-E coating. Raises the inner face about three more degrees and nearly eliminates condensation at the center of the glass. See low-E glass.
  3. A thermal break or vinyl frame. Without it, an aluminum frame keeps sweating even when the glass is dry, and the water runs onto the wall. See thermal break aluminum windows.
  4. A warm-edge spacer in the double unit, for the edge.

The sliding window track

On a slider, water running off the glass ends up in the track. Good series have weep holes: slots that drain the water outside. If they are clogged with dust or soil, water builds up and spills inward. Clearing them with a wire or compressed air once a year prevents most puddles.

What condensation leaves behind

One fogged morning damages nothing. Repeated condensation all winter does:

  • Mold on sealant, joints and the wall under the window.
  • Paint and plaster that blister or stain.
  • Wood sills and furniture near the window that swell.

If you see mold in the same place every winter, attack it from both sides: humidity and window.

How we approach it

When a client calls us about condensation, we ask about humidity first: are there gas heaters, do the bathrooms have exhaust fans, which room is wettest. Often the problem is solved without touching the window.

When it is the window, the answer is usually low-E double glazing in a thermal break or vinyl frame. We make insulated glass at our own plant and work with series from Extrusiones Metálicas, VEKA and aluplast. If your windows sweat every winter, send us photos of where the water appears and we will tell you what we would change.

Sources

  • Dew point: Magnus formula with Sonntag (1990) constants.
  • Interior surface resistance: EN ISO 6946 and EN ISO 13788.
  • Ug values: EN 673 calculation from VECA's quoting system, the same as in double-pane windows, U-factor and SHGC.

Have a technical question about your project?